Different and Unique Ways To Setup Your RangeXTD WiFi Extender

RangeXTD WiFi Extender

The RangeXTD WiFi Extender is a next-generation WiFi router that delivers a transmission speed of 300MBps. It is used to extend the existing wireless or wired range of the router. The two inbuilt antennas provide stability and cover a wide range of areas. It enhances the user experience by providing superfast network connections and lag-free gaming and video streaming. The inbuilt LED lights help the user to do the setup and also to identify the signal strength. Its range can reach every corner of the home and workplace as its range can penetrate through the walls. Over 10+ devices can be connected at the same time without any signal drop. Because of its small and sleek design,

It can also be placed everywhere even in small places. The inbuilt ventilation protects it from overheating. It has one power on/off button, reset button, mode selector, LAN port, and some LED lights. This device can also easily connect to the existing device router. The WPS button on the front allows the users to do a one-button setup. It can easily be mounted to the wall socket as it has a socket panel on its back.

The Installation Process Of RangeXTD WiFi Router

The RangeXTD wifi booster installation can easily complete by using the WPS button or by using the website browser. Here we will explain installation via the WPS button.

Installation By WPS Button

Note The LED Signal

The hardware installation of the RangeXTD WiFi Extender is simple and can do with a one-touch button. It is the easiest way to complete it. Place the repeater in the best location. The LED signal helps you to find that. There should be 2 levels of LED light on the front of the extender, if it’s not, then find a new location. 

Select Repeater Mode

Select the repeater mode position and plug the repeater into the AC socket. Press the WPS button on the extender until the LED light flashes. It may also take about 2 to 3 minutes. Press the WPS on the router when the LED light of the extender flashes. The router will automatically connect to the extender. 

Reboot The Device

The password of the RangeXTD WiFi Extender is also the same as the router’s password. Now go to the LAN settings after rebooting the device. Connect the SSID and also configure it by connecting to the computer by wire or wirelessly.

Now we gonna explain to you the various mode to set up your rangeXTD.

Modes To Setup Your RangeXTD WiFi Extender

There are different ways to set up your wifi extender. You can also set up the Extender using WiFi, Ethernet cable, and a DSL modem.

Setup RangeXTD WiFi Extender Using Wireless

Choose the repeater mode from the RangeXTD WiFi Extender and plug it into the AC outlet. The extender shows the signal on the front. There should be at least 2 signals, if it is, then the location of the extender is perfect. Otherwise, change the location. Click the connect button from the available network list. Now launch the browser and type 192.168.7.234. Enter the login details. After you successfully logged in, also choose the wizard option available on the top of the screen. Select the network option which you want to extend. Hit the Apply option after entering the unique password. The extender starts rebooting and you can also connect to the WiFi network.

Setup Using Ethernet Cable

Again select the repeater mode from the extender and also plug it into the AC outlet. If the extender shows 2 bars signal on the front, this means the location is good. Now connect the one end of the RJ45 cable to the extender via the ethernet port and another end of the cable with your system. Launch the browser and type 192.168.7.234. Fill in the login details of the rangeXTD. Select the setup wizard option available on the top left. Select the network you also want to extend. Click on the apply option after selecting the network you want to extend. Reboot the extender device and you are now able to connect your device with the new network.

Setup Using DSL Modem

Select the repeater mode and again plug it into the socket. Using RJ45 cable, connect the one end with DSL modem and another end with the rangextd WiFi extender device. Again opens the website browser by typing an IP address and also entering the login details. On the setup wizard option, choose the DHCP. Enter device parameter after clicking on the Next button and rename SSID. Select the Authentication and type the password. Now your device is rebooted and connects to your network.

What should do before using the Fritzbox networking device WiFi?

Share to aware!

Share on facebook
Share on twitter
Share on linkedin
Share on pinterest
Share on reddit
Share on whatsapp

Leave a Reply

Your email address will not be published. Required fields are marked *

Read More